ThermoPro TP620 Digital LED Thermocouple Thermometer Instruction Manual (2023)

ThermoPro TP620 Digitales LED-Thermoelement-Thermometer

Product

1. LCD display: Shows the current temperature.
2. °C/°F: Press and hold the button for 3 seconds to switch between °C and °F.
3. LOCK: Press once to lock the current temperature for 5 seconds, press again within 5 seconds to unlock.
4. Temperature probe: Insert the probe into the food to detect the internal temperature of the meat.
5. Battery compartment: Powers the device with 1 AAA battery.
6. Ultra-Fast Thermocouple Probe: High-precision sensor, you can get a temperature reading within 3 seconds.
7. CAL: Hold for 5 seconds to calibrate the device. Press again to confirm the calibration
8. Impervious: IP65
9. Sleep and wake mode with motion detection
10. built-in magnet

specification

1. Temperature range: -58°F ~ 572°F (-50°C ~ 300°C). If the temperature is below -50°C (-58°F) or 300°C (572°F), LLL or HHH will be shown on the display
2. Three buttons: LOCK/°C/°F/CAL
3. Automatic shut-off function for 90 seconds
4. Resolution: 0.1°C/°F
5. Temperature Accuracy: ±0.9°F (±0.5°C) from 14 to 212°F (-10 to 100°C)
6. Battery: 1 x AAA 1.5V included
7. Automatic screen rotation by 108°

before first use

1. Insert 1*AAA battery with correct polarity (+) and (-) as indicated.
2. Clean the probe tip with a warm soapy sponge or cloth, then rinse and dry.
3. Rinse under running water without fear!
4. Read and follow all instructions.
5. The thermometer is now ready for use.

Measure the food temperature

1. Remove the probe from the body of the thermometer to open the thermometer, and then bend the probe to close the thermometer.
2. Press and hold the °C/°F button for 3 seconds to toggle between °C and °F. Note that the selected temperature unit will be retained the next time the thermometer is turned on.
3. Insert the probe tip into the food as shown below. The thermometer starts measuring the internal temperature of the food.
   
4. Wait for the temperature reading on the screen to stabilize.
5. Temperature readings can be viewed from a global 180° viewing angle
6. Press the LOCK button to hold the temperature for 5 seconds.
7. Rinse the thermometer under running water after use.
8. The thermometer will turn off automatically when the probe is inserted and no button is pressed within 90 seconds.
9. If the thermometer is sleeping with the probe extended and then lifted or moved, the thermometer will turn on automatically.

calibration

The thermometer is calibrated. In most cases, thermometers are precisely calibrated in our manufacturing facility and you do not usually need to calibrate your thermometer. However, if after prolonged use you feel that the temperature readings displayed by the thermometer are inaccurate, you can recalibrate the thermometer as follows:

1. Use distilled or purified water to make ice cubes in the refrigerator.
2. Prepare a thermos. If it is not available, use a mug or a regular mug;
3. Fill the bottle with ice cubes (no less than 70% by volume) and top up with cold distilled or purified water (no more than 30% by volume).
4. Stir the mixture and leave for 10 minutes to allow ice and water to reach equilibrium temperature;
5. Open the thermometer, unscrew and remove the battery cover.
   
6. Submerge the probe in the ice and water mixture, being careful not to touch the sides of the container. Wait for the temperature reading to drop to its lowest reading, which should be around 32°F or 0°C. If the temperature of the ice/water mixture is not between 28°F and 36°F (or -2°C and +2°C), the calibration cannot proceed: you must prepare the ice/water again Mix as specified below. above;
7. Press and hold the CAL button for 5 seconds to enter calibration mode. CAL is displayed for 3 seconds and the current temperature is displayed on the screen.
8. Press the CAL button once to confirm and exit calibration mode.

Nuts:
Calibration mode only takes 15 seconds. If you cannot calibrate within 15 seconds, the thermometer will exit calibration mode automatically.

Undo calibration

If you want to undo the calibration and return to the default calibration settings, do the following:

1. Turn on the thermometer and press the “CAL” button for 5 seconds to enter calibration mode.
2. Press the lock button to cancel the calibration and it will reset to default.

Helpful tips

• When measuring different foods or meats, it may be necessary to first rinse the tip with cold water to cool the probe.
• It is recommended to clean the probe tip between measurements. This is especially important when measuring the temperature of different foods or meats.
• This thermometer is designed for occasional hand use. Do not use in the oven. Do not place in extremely hot (above 572°F) food or liquid for more than 1 minute.
• Always read the thickest meat. Thin cuts of meat are difficult to measure because they tend to cook quickly. Avoid touching the bone. If the tip touches the bone or thick fat area of ​​the meat, or if the tip isn't deep enough, read again to ensure accuracy.
• It is not intended for use by persons under the age of 12.

Take good care of your thermometer

• Do not touch the stainless steel part of the thermometer during or immediately after taking the temperature as it will be hot.
• Do not expose it to extreme heat or cold as this can damage electronic parts and plastics.
• Do not stick the thermometer into the food while cooking.
• If the device will be stored for more than four months, remove the batteries.

Declaration of Conformity

The manufacturer hereby declares that this product meets the essential requirements of EN and is suitable for compliance with the essential requirements and applicable standards of the EMC Directive 2014/30/EU. The complete declaration of conformity can be found at:https://itronicsmall.com/eu-declaration-of-conformity/

get over

• Protect our environment: Do not dispose of electronic devices with household waste.
• Please hand in electronic devices that you no longer use to the designated collection point for disposal.
• This helps to prevent potential impacts of incorrect disposal on the environment and human health.
• This will facilitate recycling and other forms of reuse of electrical and electronic equipment.
• Information on where the devices can be disposed of can be obtained from your local authorities.
• The battery must be removed from the device.
• Dispose of used batteries at a suitable collection point or at the retailer.
• You can obtain information on public collection points from your city or municipality.

You will find this symbol on batteries/rechargeable batteries that contain dangerous substances.

Customer service

Telephone:1-877-515-7797 (US and Canada only)
44-808-164-1683 (UK)
Email: service@buythermopro.com
Hour:Weekdays 8:00 a.m. to 8:00 p.m
EST (US and Canada only) Monday through Friday from 1:00 p.m. to 5:00 p.m. M. to 12:00 M. CET (UK)

Documentation/Resources